Posts Tagged ‘Halloween’

Halloween Embroidery & Candle Shade Designs, 1912

Embroidery-Design-for-Halloween

If you are planning for Hallowe’en festivities, you will be pleased with this appropriate design. It can be easily and quickly worked in outline, with heavy thread. The natural, bright colors of Autumn should be used. A table runner and sofa pillows would be novel and once made, could be used for several Hallowe’ens.

Halloween-candle-stencil

Candle shades made after this fashion will prove very attractive for Halloween, and as they are extremely simple of execution, it will be very little trouble to manufacture a number of them for various uses about the house for the Hallowe’en party. The stencil might be cut from heavy yellow paper and lined with black tissue paper. A number of the shades may be cut at one time, which will save trouble. The shade is especially pretty in shape when fastened with gum or mucilage at one side.

Here’s a drawing of a candle shade holder I think could be made out of wire.

candle shade holder

3 comments

Halloween Costumes You Can Make, 1922

Do you think home sewers and crafty people in the 1920s could actually create these costumes with the unbelievably limited directions the publishers give in these articles?  I have my doubts. Still, the illustrations are pretty cute.

1922-Halloween-Costumes-1 1922-Halloween-Costumes-2 1922-Halloween-Costumes-3

Most of the costumes have no instructions at all (simply suggesting you apply fabric or crepe paper to a foundation garment), and there is no mention of a mail order pattern. Also, there was no hot glue!

Here are the individual directions given for three of the costumes in the last illustration.

Frog Costume:  A frog costume is unusual and distinctive. It may be made of cambric, chambray, sateen, satinette or poplin. This costume is suitable for adults, misses and juveniles.

Witch Costume: Witch costumes are always seen at fancy dress occasions. A 36″ bust requires 13 3/4 yards [this is not a typo!] of 36″ sateen. The lower edge measures 2 1/2 yards and can be worn by all.

Pierette Costume: A Pierette costume is pretty for women, misses and juveniles of 26 to 40 bust. A 36″ bust requires 4 1/2 yards of 40″ organdy for ruffles, etc., 5/8 yard of 40″ satin for sash and top of hat and 5/8 yard of 36″ satin for camisole. The costume, as can be seen in the accompanying drawing, is of peg-topped effect at the waist, tapering down to form to the ankle.

So . . . just pull out an old slip, grab some cambric, tulle, crepe paper or cheesecloth, and whip up one of these adorable costumes. Then send me your photos.

1 comment

Vintage Halloween Screen Instructions

I’ve had several requests from readers who wanted to make the Halloween screen I gave to my sister a couple of years ago, which I copied from an embossed 1920s Halloween decoration that I found online. Since my sister has the screen, I can’t provide detailed photos, but I can give you a pattern, a list of supplies, and some instructions. This is my finished screen.

Vintage-Inspired-Halloween-Screen

It is 24″ wide and 20″ high, which is the same size as the original decoration.

Supplies:
One sheet of heavy black poster board (the Walmart/Dollar Store poster board is too thin)
8 24″ strips of 1/2″ x 1/4″ basswood (available at most craft stores)
small amount of black paint
orange flat fold crepe paper
Xacto knife
spray adhesive
white pencil
white glue
black electrical tape

Instructions:
Click this link to download the pdf pattern. In the Adobe print dialog box, select the poster setting. This will tile print the pattern on 9 sheets of paper (3 for each panel). You will need to trim two sides of each sheet of paper before taping or gluing the sheets together.

Paint the strips of basswood black.

Using an Xacto knife or small scissors, cut out the white sections of the paper pattern, then draw the pattern on the back side of your poster board with a white colored pencil  (if you have some white or light-colored carbon paper, you could use it to transfer the pattern, eliminating this step). Once the pattern is transferred to the poster board, cut out all the interior white sections of each panel with an Xacto knife, then cut the outside lines.

Cut three pieces of orange crepe paper slightly smaller than the three panels of the screen (iron the crepe paper if it is wrinkled — you want it very flat). One at a time, place each cut black panel (right sides down) on newspaper and spray adhesive on the back. Carefully place your cut piece of crepe paper on the back of each section, trying to keep them as flat as possible.

Using a razor blade or sharp knife, trim the strips of basswood to fit the sides and bottom of each of the screen panels. Apply a thin layer of white glue to one side of each basswood strip and position the wood strips flush with the outside edges of each panel — let dry.

Position the three panels face down, pushing them as close together as possible. To make the hinges, apply two strips of black electrical tape to the wood strips along both seams, attaching the two outside panels to the center panel.

I hope this makes sense — let me know in a comment if you have any questions.

2 comments